IS:7084
IS:7084IS:7084
IS:7084
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
A0302
Page 3 of 3
A
COMPANY
631 Airport Road, Fall River, MA 02720
D. ACCESS TO JUNCTION BOX FROM BELOW
1) Switch off power to fixture at service panel.
2) Remove CONE (Fig. 11) and LAMP PROTECTIVE
GLASS SHEILD.
3) Remove tungsten halogen lamp (
CAUTION: Do not
touch with bare hands. Oil from hands could
reduce LAMP life. Use tissue paper or cloth when
relamping
).
4) Locate SLIDE LATCH on HOUSING SUPPORT.
Push out to the right to disengage SLIDE LATCH
from SLOT of REFLECTOR (Fig. 12). Repeat for
other two latches.
5) Push RFLECTOR up and to the side to provide
access to JUNCTION BOX. (Fig. 12).
6) To access JUNCTION BOX, lift up JUNCTION BOX
SPRING to remove JUNCTION BOX DOOR (Fig. 12).
7) After servicing, push all wires back inside JUNCTION
BOX. Insert TABS of JUNCTION BOX DOOR into
slots of JUNCTION BOX and align NOTCH of
JUNCTION BOX DOOR with JUNCTION BOX
SPRING. Snap JUNCTION BOX DOOR onto
JUNCTION BOX firmly (Fig. 12 and 13). Make sure
JUNCTION BOX DOOR is not pinching wires.
8) Install REFLECTOR back into HOUSING SUPPORT
(Fig. 13). For easier installation, the conduit from
socket to junction box should be positioned as shown
in Fig. 13.
9) Feel through the slots to align SLOTS of
REFLECTOR with SLIDE LATCHES. Note: SLIDE
LATCHES may not be visible from below, it is
recommended to first align the slot with the latch
opposite to junction box, then place REFLECTOR on
inside of HOUSING SUPPORT (Fig. 13).
10) Slide SLIDE LATCH to the left and pull back to
secure REFLECTOR (Fig. 13). Repeat for the other
two latches.
11) To ensure REFLECTOR is properly, rotate
REFLECTOR slightly to ensure SLIDE LATCHES
engage with SLOTS in REFLECTOR. The
REFLECTOR should not rotate if it is in locked
position.
12) Install lamp (see
CAUTION
in item 3 above).
13) Place LAMP PROTECTIVE GLASS SHIELD on top of
HOUSING SUPPORT (Fig 1).
14
Install CONE
Ste
C above
E. CARE AND MAINTENANCE OF “ALZAK”
REFLECTOR
If handling of reflectors with anodized or Alzak finish is
required, the use of clean white or plastic film gloves is
recommended to avoid fingerprints.
Anodized or Alzak surfaces can be cleaned by the
following methods:
1) Wipe off with a soft, clean, dry, lint-free cloth.
2) Wipe off with a soft, clean cloth dampened in mild
detergent solution. Rinse, then wipe dry with a lint-
free cloth or paper towel.
3) Wipe off with a clean cloth dampened with a solution
of wetting agent and water (such as 2 oz. per gallon)
“Pluronic L62-F” by Wyandotte Products). Then wipe
dry.
4) Or use a liquid wash such as Glass Wax
. Avoid
gritty cleaning agents.
TAB
JUNCTION BOX
SPRING
JUNCTION BOX
JUNCTION BOX
DOOR
REFLECTOR
REFLECTOR
SLOT
HOUSING SUPPORT
SLIDE LATCH
FIG. 12
FIG. 13
SLOTS
SLIDE LATCHES
HOUSING SUPPORT
REFLECTOR
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals