Lightolier LSB-10 User Manual download pdf

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

"JSQPSU3PBE'BMM3JWFS."tt'BY

We reserve the right to change details of design, materials and finish.

XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt

Lighting Systems LSB-10

1BHFPG -ZUFTQSFBEÜ-4#1BSBCPMJD-PVWFS-JHIU51FS'PPU/PNJOBM4FDUJPO

#

Features

1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with

no exposed fasteners or hardware.

2. Lamping: Two T5, 28 or 54 watt (as specified) fluorescent lamps per 4-foot

nominal section. Provided by others.

3. Reflector: Precision die-formed semi-specular aluminum.

4. Louver: Parabolic louver, low-iridescent semi-specular anodized aluminum,

41° shielding lengthwise, blades are 1-1/3” (3.39cm) high and 2” (5.08cm) O.C.

Louver frame is extruded aluminum and finished to match housing.

Electrical

Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-

coded quick connectors allow ease of connection for joiner modules. Power feed

is 18 gauge white SJT. For special circuiting consult factory. Factory installed

ballast disconnect allows the ballast to be disconnected from and reconnected to

incoming power under load without turning the entire circuit off.

Dimming: 120/277 V

AC 1% dimming level, 4 wire feed required.

Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700

lumens @ 90 minutes, 4 wire feed required.

Mountings

Finish

Powder coated baked white or aluminum finish. Custom colors available, consult

factory.

Options and Accessories

Emergency Circuiting; special circuiting; X, T & L joiner blocks - consult factory.

Labels

UL, cUL and I.B.E.W.

Ordering Instructions

Individual Fixtures:

1. Order number of MODULES required.

2. Order one POWER FEED END SET per MODULE.

Continuous Rows:

1. Determine run length.

2. Order the appropriate number of MODULES for the complete run.

3. Order one POWER FEED END SET per run.

4. Order one CABLE ASSEMBLY per MODULE minus one per run.

5. For runs that exceed amperage limits, order the appropriate

number of CABLE/CORD ASSEMBLIES.

Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white

enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"

(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner

modules.

Complete ordering instructions below.

Ordering Information

Family Lamps Voltage Finish

2 = 2-Lamp T5 C = Parabolic Louver AL = Aluminum

WH = White

LSB 2 C

Length Shielding Ballast

1 = 120 volt

2 = 277 volt

28 = 28W T5

54 = 54W T5

5E = 54W T5 Emergency Pack

2E = 28W T5 Emergency Pack

5D = 54W T5 Dimming

4 = 4-Foot

8 = 8-Foot

Half Scale

8 1/2" (216 mm)

1 3/4" (37.5 mm)

3 1/4" (82.6 mm)

2 5/8" (66.7 mm)

1 2

Lighting Systems LSB-10 1

Summary of Contents

Page 1 - Lighting Systems LSB-10

Job Information Type:Job Name: Cat. No.: Lamp(s): Notes: "JSQPSU3PBE'BMM3JWFS."tt'BY

Page 2

Job Information Type:"JSQPSU3PBE'BMM3JWFS."tt'BYWe reserve the right to change d

Comments to this Manuals

No comments

Lightolier LSB-10 User Manual

Browse online or download User Manual for Unknown Lightolier LSB-10. Lightolier LSB-10 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Lightolier LSB-10