Lightolier LSB-6 User Manual download pdf

Job Information Type:

Job Name:

Cat. No.:

Lamp(s):

Notes:

"JSQPSU3PBE'BMM3JWFS."tt'BY

We reserve the right to change details of design, materials and finish.

XXXMJHIUPMJFSDPN½1IJMJQT(SPVQt

Lighting Systems LSB-6

1BHFPG -ZUFTQSFBEÜ-4#1JFSDFE-VNJOPVT*OEJSFDU-JHIU51FS'PPU/PNJOBM4FDUJPO

#

Features

1. Housing: Extruded aluminum. Die-cast end cap mechanically attached with

no exposed fasteners or hardware.

2. Lamping:

nominal section. Provided by others.

3. Reflector: Precision die-formed semi-specular aluminum.

4. Shielding: Precision die-formed, pierced 20 gauge CRS. Piercing is four rows

that extend the entire length of the lamps. The pattern is 5/8” (1.59cm) x 1/16”

(0.16cm) slot with a 3/16” (0.48cm) separation between rows.

Electrical

Ballast is <10% THD, .98 ballast factor, pre-heat start. 18 gauge wire. Color-

coded quick connectors allow ease of connection for joiner modules. Power feed

is 18 gauge white SJT. For special circuiting consult factory. Factory installed

ballast disconnect allows the ballast to be disconnected from and reconnected to

incoming power under load without turning the entire circuit off.

Dimming: 120/277 VAC 1% dimming level, 4 wire feed required.

Emergency Battery Pack: 28 watt: 520 lumens @ 90 minutes, 54 watt: 700

lumens @ 90 minutes, 4 wire feed required.

Mountings

Finish

Powder coated baked white or aluminum finish. Custom colors available, consult

factory.

Labels

UL, cUL and I.B.E.W.

Ordering Instructions

Individual Fixtures:

1. Order number of MODULES required.

2. Order one POWER FEED END SET per MODULE.

Continuous Rows:

1. Determine run length.

2. Order the appropriate number of MODULES for the complete run.

3. Order one POWER FEED END SET per run.

4. Order one CABLE ASSEMBLY per MODULE minus one per run.

5. For runs that exceed amperage limits, order the appropriate number of

CABLE/CORD ASSEMBLIES.

Options and Accessories

Emergency Circuiting; special circuiting; X, T & L joiner blocks - consult factory.

Complete ordering instructions below.

Cable suspension (not shown) - 4-1/2" (11.43cm) diameter canopy finished white

enamel, 1/16" (0.16cm) diameter stainless steel aircraft cable adjustable up to 36"

(91.44cm). Dual-screw draw-tight connector to create hairline seam between joiner

modules.

Ordering Information

Family Lamps Voltage Finish

2 = 2-Lamp T5 B = Pierced AL = Aluminum

WH = White

LSB 2 B

Length Shielding Ballast

1 = 120 volt

2 = 277 volt

28 = 28W T5

54 = 54W T5

5E = 54W T5 Emergency Pack

2E = 28W T5 Emergency Pack

5D = 54W T5 Dimming

Two T5, 28 or 54 watt (as specified) fluorescent lamps per 4-Foot

4 = 4-Foot

8 = 8-Foot

Pierce Pattern

3-1/2" (8.89cm)

3/16"

(0.48cm)

5/8"

(1.59cm)

3-1/16"

(7.78cm)

1/16"

(0.16cm)

2 4

Fixture Shown Half Scale

8-1/2” (21.59cm)

1-3/4" (4.45cm)

1 2

Lighting Systems LSB-6 1

Summary of Contents

Page 1 - Lighting Systems LSB-6

Job Information Type:Job Name: Cat. No.: Lamp(s): Notes: "JSQPSU3PBE'BMM3JWFS."tt'BY

Page 2

Job Information Type:"JSQPSU3PBE'BMM3JWFS."tt'BYWe reserve the right to change d

Comments to this Manuals

No comments

Lightolier LSB-6 User Manual

Browse online or download User Manual for Work lights Lightolier LSB-6. Lightolier LSB-6 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Work lights Lightolier LSB-6