Lightolier IS:6079 User Manual download pdf

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE

ThisfixtureisintendedforinstallationinaccordancewiththeNational

Electrical Code and load regulations.

To assure full compliancewithlocalcodesandregulations,checkwithyourlocalelectricalinspector

before

installation. Toprevent electrical shock, turnoff electricity at fuse box before proceeding.

Retain these instructions for maintenance reference.

INSTRUCTION SHEET NO.

IS:6079

0493

Page 1 of 2

INSTALLATION FOR AITACHING EXTENSION WAND SLOPED CEILINGS ADAPTER

TO LYTESPAN TRACK. FOR USE WITH LYTESPAN” TRACK SYSTEMS ONLY

Extensionwandslopedceilingadaptercanbe mountedon anyBasic,Advent Multipointor MonopointTrackon tailings from 0° to 90° (vertical).

Notfor usewith Lytespota with attachmentfitting 7589.

Grasp TOP FITTING at top of ADAPTER and insert it into the LYTESPAN TRACK. The LOCKING LEVER must be on the same side of the track as the BEAD.

(see Fig. 1.)

2. Rotate the TOP FI’ITING W’ clockwise, (See Fig. 2), untilLOCKING LEVER snaps and locks in plats. (See Fig. 3.) Do not rotate adapter from LOWER FllllNG.

3. Loosen KNOB and set the lower haff of the ADAPTER to a vertical positionand tighten KNOB. (Fig, 4)

4. To Remove Depress LOCKING LEVER; then rotate TOP FllllNG 90° counter-dockwke. Do not rotate wand from LOWER FITTING,

BEAD

LOCKING

LEVER

FIG. 1

LVTESPAN

TRACK

FITTING

-u

CLOCKWISE

FIG. 2

!l-

FIG. 3

‘“WERF’”’N

I I

FIG. 4

INSTRUCTIONS

FOR CONVERTING FITTING TO OPERATE ON

2 CIRCUIT TRACK SYSTEMS

BRASS CONTACT

See Fig.5, BRASS CONTACT can be raisedor lowered,Brokenlineindicatespositionfor 1 circuit

trackor lowercircuitof2 circuittracksystem.

L::;;:G

To mnverf attachment FllTING for upper circuitof 2 circJJittrack, raise BRASS CONTACT to high

positionby Ming CONTACT as high as stop f.wrnits and CONTACT clicks into place.

FIG. 5

INSTRUCTIONS FOR AllACHING EXTENSION WAND TO EXTENSION WAND SLOPED CEILING ADAPTER

Insert the WAND FllllNG into the LOWER FllllNG.

The LOCKING LEVER must be on the same side as the bead located at the bottom of the LOWER FllTING (See Fig. 6.) Rotate the WAND FllllNG

90° clockwise until LOCKING LEVER snaps and locks in place. (See Fig. 6,7, & 8).

2, To remove, depress LOCKING LEVER and rotate FllllNG 90° counterclockwise.

/-R/la

BEAD BRASSCONTACT

“OWN

LOCKING_

_ WAND

CLOCKWISE

LEVER

FllTNG

FIG. 6

FIG. 7

FIG. 8

1 2

Summary of Contents

Page 1 - ‘“WERF’”’N

rREAD AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTUREThisfixtureisintendedforinstallationinaccordancewiththeNationalElectrical Code and lo

Page 2 - INSTRUCTION SHEET NO

*-INSTRUCTION SHEET NO.1s:6079INSTALLATION FOR AITACHING EXTENSION WAND SLOPEDCEILINGS ADAPTER TO LYTESPAN TRACK. FOR USE WITH0493 Page 2 of 2LYTESPAN

Comments to this Manuals

No comments

Lightolier IS:6079 User Manual

Browse online or download User Manual for Unknown Lightolier IS:6079. Lightolier IS:6079 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Lightolier IS:6079