Figure A
Figure B Figure C
Figure D Figure E
Figure F
Figure G Figure H
READ AND UNDERSTAND THESE INSTRUCTIONS
BEFORE INSTALLING LUMINAIRE.
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at main power supply before proceeding.
Retain these instructions for maintenance reference.
INSTALLATION PROCEDURE FOR: LYTECASTER® 2000LVRE1 LOW VOLTAGE REMODELER KIT
CAUTION: USE ONLY WITH REFLECTOR TRIMS PROVIDED BY LIGHTOLIER. USE OF OTHER MANUFACTURER’S TRIMS MAY VOID THE
UNDERWRITERS LABORATORIES LISTING AND COULD CONSTITUTE A FIRE HAZARD.
INSTRUCTION SHEET NO.
IS:2000LVRE1
A0607
Page 1 of 2
A COMPANY
631 Airport Road, Fall River, MA 02720
CAUTION: BEFORE INSTALLING FRAME-IN KIT AND REFLECTOR TRIM, READ ALL MARKINGS ON FRAME-IN KIT AND REFLECTOR TO
DETERMINE LAMP WATTAGE AND TYPE APPLICABLE FOR YOUR INSTALLATION.
1. CUT OPENING (Fig. A)
Use aperture sticker provided as a template to cut a hole in the ceiling. Cut to
outside edge of sticker.
* Lightolier also offers a hole cutter (HC-356) that can be purchased separately to
assist with quick, clean trim installations. In this case, follow the hole cutting
directions supplied with HC-356.
2. WIRE IN & PUSH THRU
Wire to SUPPLY LEADS. (For Cable, use built in CABLE CLAMP in J-BOX).
WHITE FIXTURE LEAD to NEUTRAL SUPPLY LEAD. BLACK FIXTURE LEAD to
HOT SUPPLY LEAD (120V). GREEN AND BARE FIXTURE LEAD WIRE TO
SUPPLY GROUND. Use wirenuts (local hardware item). Place all electrical
connections in J-Box. Attach J-BOX cover onto J-BOX. For flexible CONDUIT, use
90° connector (not supplied) or 3/8” SPRING CONNECTOR (provided). If 3/8”
SPRING CONNECTOR is used, place J-BOX and TRANSFORMER ASSEMBLY
onto ceiling, attach CONNECTOR to CONDUIT and push into one of the 7/8” dia.
knock out holes in J-BOX. Pull J-BOX and TRANSFORMER ASSEMBLY toward
ceiling opening (as shown in Figure B) and complete wiring.
3. ATTACH MOUNTING RING (Fig. D)
Push MOUNTING RING into opening until FLANGE sits against ceiling.
Slide MOUNTING STRAPS down to trap ceiling thickness and then bend up
to secure (Fig. E). Make sure “J-BOX” SLOT on REMODELER RING is in a
position that will ensure enough space above ceiling for J-BOX to sit flat
against ceiling.
4. ATTACH J-BOX (Fig. E)
Insert J-BOX MOUNTING STRAP between the ceiling material and MOUNTING RING and through the
“J-BOX” SLOT on the MOUNTING RING. Pull the STRAP until the J-BOX PLATE sits flat on the
ceiling with the feet over the edge of the ceiling thickness. Bend J-BOX PLATE MOUNTING STRAP
up to secure. Make sure J-BOX PLATE is securely attached to the ceiling and the J-BOX is in the
shown position.
5. SNAP-ON (Fig.G)
→
6. PUSH-UP (Fig. H)
SEE SEPARATE
REFLECTOR TRIM
INSTRUCTION
SHEETS
WARNING: (RISK OF FIRE) DO NOT INSTALL INSULATION WITHIN 3” OF FIXTURE SIDES OR WIRING COMPARTMENT, NOR ABOVE
FIXTURE IN SUCH A MANNER SO AS TO ENTRAP HEAT.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals